当前位置: 产品列表 产品详情
< >

0.96" OLED,128×64分辨率 ,SSD1315Z IC,30PIN,3/4线串行接口,I2C

SCE096009-V01是一款COG类型的OLED显示屏,128×64分辨率,SSD1315Z IC,3/4线串行接口,I2C,30PIN

  • Type: OLED
  • Mode: -
  • Product No: SCE096009-V01
  • Size: 0.96''
  • Resolution: 128×64
  • Outline Dimension: 24.74*16.90*1.42
  • Active Area: 21.74*10.86
  • Interface: I2C//
  • IC: SSD1315Z
  • Brightness: -
  • Touch Screen: No
  • View Direction: -
  • Pin No: 30
  • Shape: 长方形
立即询价

介绍:

 General Specification

 

ITEMSPECIFICATIONS UNIT
  MODULE SIZE24.74(W)x16.9(H)x1.42(D)mm
  VIEWING AREA22.74 (W) x 11.86(H)mm
  ACTIVE AREA21.74 (W) x10.86(H)mm
  DOT SIZE0.15(W) x0.15(H)mm
  DOT PITCH0.17(W) x0.17 (H)mm
  ASSY.TYPECOG
  WEIGHTTBD

Interface Definition

 

PIN NO.SYMBOLTYPEFUNCTION DESCRIPTIONS
1NC(GND)PIt should be connected to external ground.
2C2P
C1P/C1N-Pin for charge pump capacitor.
C2P/C2N-Pin for charge pump capacitor.
Connect to each other with a capacitor. They must be floated when the
Charge pump not use.
3C2N
4C1PI
5C1N
6VBATPPower supply for charge pump regulator circuit.
It must be connected to external source when charge pump is used. It must be float when charge pump is not used.
7NC
NC
8VSSPGround pin. It must be connected to external ground.
9VDDPPower pin for logic circuit. It must be connected to external source.
10BS0IInterface selection pins.


BS0BS1I2C013-wire SPI104-wire SPI00
11BS1
12NC
NC.
13CS#IChip Select input pin. Active “L”
14RES#IHardware reset input pin. Active “L”.
15D/C#IThis is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0]  is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS
16NC
NC.
17NC
NC.
18D0I/OWhen serial interface mode is selected,D2 should be either tied LOW or tied together with D1 as the serial data input: SDIN, and D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0
is the serial clock input, SCL.
19D1
20D2
22NC
NC.
23NC
NC.
24NC
NC.
25NC
NC.
26IREFICurrent reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.
27VCOMHOCOM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
28VCCPPower supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used.
It must be connected to external source when charge pump is not used.
29VLSSPThis is an analog ground pin. It should be connected to VSS externally.
30NC(GND)PIt should be connected to external ground.


上一页 上一个产品 : 0.96英寸OLED,128×64分辨率 SSD1306 IC 4个SPI接口 15PIN

下一个产品 : 0.96''OLED显示屏,64×128 ,SH1107 IC 13PIN 下一页