当前位置: 产品列表 产品详情
< >

1.54"OLED, 128×64分辨率, COG类型 ,SPD0301ZD IC

SCE154001-V01是一款COG类型的OLED显示屏,128×64分辨率,SPD0301ZD IC,6800/8080接口,4线串行接口,I2C,30PIN

  • Type: OLED
  • Mode: -
  • Product No: SCE154001-V01
  • Size: 1.54''
  • Resolution: 128*64
  • Outline Dimension: 42.04*27.22*1.41
  • Active Area: 35.052*17.516
  • Interface: 6800/8080
  • IC: SPD0301ZD
  • Brightness: -
  • Touch Screen: No
  • View Direction: -
  • Pin No: 24
  • Shape: 长方形
立即询价

介绍:

General Specification

 

ITEMSPECIFICATIONS UNIT
 MODULE SIZE42.04(W)x27.22(H)x1.41(D)mm
 VIEWING AREA37.052 (W) x 19.516(H)mm
 ACTIVE AREA35.052(W) x17.516(H)mm
 DOT SIZE0.254(W) x0.254(H)mm
 DOT PITCH0.274(W) x0.274 (H)mm
 ASSY.TYPECOG
 WEIGHTTBD

Interface Definition

 

PIN NO.SYMBOLTYPEFUNCTION DESCRIPTIONS
1NC(GND)PIt should be connected to external ground.
2VLSSPThis is an analog ground pin. It should be connected to VSS externally.
3VSSPGround pin. It must be connected to external ground.
4NC
NC
5VDDPPower pin for logic circuit. It must be connected to external source.
6BS1I

Interface selection pins.

I2C680080804SPIBS11010BS20110
7BS2
8CS#IChip Select input pin. Active “L”
9RES#IHardware reset input pin. Active “L”.
10D/C#IWThis is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0]  is data.
When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS
11R/W#IThis is read/write control input pin.
8080: data write enable; 6800: read/write select pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
12E/RD#IThis is read/write control input pin.
8080: data read enable; 6800: read/write enable pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
13D0I/OThese are 8-bit bi-directional data bus to be connected to microprocessor’s Data bus.
When serial interface mode is selected, D2 should be kept NC, D1 will be the serial data input: SDIN, D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0 is the serial clock input, SCL.
14D1
15D2
16D3
17D4
18D5
19D6
20D7
21IREFICurrent reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 10 uA maximum.
22VCOMHOCOM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
23VCCPPower supply for OLED driving voltage. A capacitor should be connected between this pin and VSS.
24NC(GND)PIt should be connected to external ground.


上一页 上一个产品 : 1.41''MIPI OLED,320*360分辨率,ZTW522 IC

下一个产品 : 2.7''OLED显示器, 128×64分辨率,SSD1325 IC 下一页